The legs should be flush to the edge of the back edge of the desktop.Īttach the legs using Simpson GA2 Brackets using #8 x 1 in. Space the legs 1-½’’ from the 3 of the edges. Measure and space out the 3 assembled legs. Attach the desk legs to the BOTTOM of the desktop: You could also use a circular saw with a straight edge tool as a guide. We find it easiest to use a table saw for clean straight cuts. Your local home improvement may be able to cut the plywood for you and get the measurements close. In this case we made the desk 24’’ x 84’’. Measure the desktop on your sheet of plywood to the final desk dimensions. Now attach the 19.5’’ bottom support to the bottom half, leaving about a 3’’ gap from the bottom of the legs to the bottom of the support using two 3’’ long screws on each face into the support. 2×4Īssemble the legs by attaching the two 27’’ vertical legs to the 22.5’’ top plate using 2 screws into each leg. How to maximize the cut sizes on a 10 ft. Cut & Assemble Wood Desk LegsĬut the 2×4’s into the following lengths: Phillips Lath ScrewsĮstimated time for completion: 8+ Hours Step by Step Instructions: 1. 1 – 4’x8’ ¾’’ Sheet of Sandee Plywood (Cabinet Grade).Here’s what you’ll need to build an easy DIY wood desk for about $100 or less. The plan was to keep the desk as a craft space for all of my Cricut projects when the need to work from home was over. The goal was to only need some 2x4s and plywood, but not look like work bench. Steven got to work drawing up plans in an effort to make a desk that felt useable, but without spending a small fortune on it. We thought about using a folding table, but it was too small and just not built to support all the computer gear he needed. Thankfully we had the space, but buying a desk for a couple hundred dollars for a temporary situation just didn’t feel rational. We’ve never dealt with needing an additional home office before! What’s a DIY-er to do? Build an easy DIY wood desk! I was already working from home in our home office, but Steven found out he’d soon be working from home too. There are numerous stain options available but, you need to consider how long it will take for the stain to dry and factor that into your project time frame.The time is COVID-19 pandemic. Next, you may want to think about if you’ll need to stain the table legs. All you practically need to do now is select the best option and deck up your home with the unique and uplifting table leg design you’ve implemented! Because we have covered table legs DIY options in all available table types, you’ll be truly spoils for choices. Now that you’ve checked our entire list, you will probably have an easier time exploring the many options and zeroing in on just the right table leg design. In most cases, you will simply need to place each leg against two of the desk’s existing legs and screw them in.Īnd that’s it! You’ve now made your own legs for a desk or table. This will vary depending on what type of desk you have, so we recommend checking your desk’s assembly instructions for specific instructions. The last step is to attach the legs to your desk. Repeat this process for the other three legs.Ĥ. Do not over-tighten the screws, as you don’t want them to come loose later on. Now it’s time to assemble the legs! Place one leg on a flat surface and screw in the screws from the bottom. Be sure to pay special attention to the ends of the legs, as these will be visible once the desk is assembled.ģ. Use your sandpaper to smooth out any rough edges. Next, it’s time to sand down the edges of the wood. These will be used for the screws later on.Ģ. Then use your drill to make two holes in each leg that are about two inches from the bottom. Use your jigsaw to cut out two legs that are about 22 inches long. Once you have gathered your supplies, it’s time to start building! The first step is to cut the wood into four equal pieces. We recommend using a piece of lumber that is at least two inches thick.ġ. The size and shape of the wood you choose is up to you. The first step is to gather your supplies. How to Make Your Own Desk and Table Legs: A Step-by-Step Guide The legs are made of solid metal and thus durable and efficient. This table follows a unique design, and you will only need four basic power tools to get started.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |